Skip to content
Home > Series > PEM > C

C Series

Switch with EIEC Connector Compact Size

UL Recognized
CSA Certified
VDE Approved‡

Catalog Data Sheet

C Series

Two function power entry module combining a DPST switch and an IEC 320 power line connector. Compact packaging allows a smaller panel cutout with choice of snap-in or flange mounting. Available with general purpose filtering (F models - CFS, CFE), medical application filtering (H models - CHS, CHE) or unfiltered (CS, CE). Terminals allow for easy connection to any wiring scheme. Preconnected terminals from line to switch are available (B Models - CBS, CBE) for reducing OEM wiring time.

The medical versions (H models) are designed specifically for health care applications. Their extremely low leakage current allows compliance with UL544 and UL2601 health care specifications for use with both patient and non-patient care equipment.

Unfiltered versions are available in either 10 amp or 15 amp versions.

See Appendix C for more information on UL544 or UL2601 health care applications.

Note: When using the models with an IEC connector, remember that the leakage current of the companion line cord, GA400, is more significant than that of the filter - which may disqualify this line cord from use in patient care applications.

‡ 15A versions tested by Underwriters Laboratories to US and Canadian requirements and are VDE approved at 10A, 250VAC

Electrical Schematic

F Models (CFS, CFE)

H Models (CHS, CHE)

B Models (CBS, CBE)

Resistor location for reference only

Specifications

Maximum leakage current, each line to ground †:
    F Models H & Unfiltered Models
  @ 120 VAC 60 Hz .25 mA 2 µA
  @ 250 VAC 50 Hz
 .40 mA 5 µA
     
Hipot rating (one minute):
  line to ground 2250 VDC 1500 VAC
  line to line 1450 VDC 1450 VDC
     
Operating Frequency: 50 / 60 Hz
     
Operating voltages: 115/230 VAC
     
Rated Current: 1 to 15 Amps
  * refer to part number for rating
   
Switch: Double-insulated rated for 10,000 operations at full load.
51 Amp inrush capability.
   
Output Terminal
Push-on Force: 		18 lb / 80N
Switch Terminal
Push-on Force: 		15 lb / 67N
Minimum insertion loss in dB: †
Line to ground in 50 ohm circuit
Current Rating Frequency - MHz
.05 .15 .5 1 5 10 30
F Models
1A 10 26 46 48 46 47 46
3A 8 16 32 36 43 48 50
6A 4 11 22 27 36 41 50
10A 1 4 14 18 27 33 42
H Models
1A 16 21 37 44 26 21 10
3A 9 14 31 32 26 24 14
6A 4 10 22 23 19 18 13
10A 2 6 10 15 11 11 9
Line to line in 50 ohm circuit
Current Rating Frequency - MHz
.05 .15 .5 1 5 10 30
F Models
1A 1 3 13 28 62 67 42
3A 2 6 14 23 65 65 67
6A 2 6 14 27 46 48 58
10A 1 7 14 23 42 44 62
H Models
1A 1 6 13 29 38 42 26
3A 1 5 10 22 36 34 36
6A 1 5 14 20 31 33 37
10A 1 4 11 19 32 37 38
 
† Applies to Filtered Models only

Case Styles

CS, CBS

CE, CBE

Typical Dimensions
Mounting Holes (2) .132 Dia with .260 x 90° countersunk for#4 Flathead Screw
3.35
IEC Terminals (3) .250 Switch Terminals (4) .188
6.35 4.8
Holes (2) .07 Dia. Holes (4) .059
1.8 1.5
Slot
 .07 x .16    
1.8 x 4.1    

CFE, CHE

CFS, CHS

Typical Dimensions
Terminals (3) .250 Holes (2) .07 Dia.
6.35 1.8
Slot .07 x .16 Mounting Holes (2)
 .132 Dia
1.8 x 4.1 3.35
    with .260 x 90° countersunk for#4 Flathead Screw

CBS, CBE Pre-Connected Terminals

 

Recommended Panel Cutout

Panel Cutout for thickness of .031 - 0.98 [.8-2.5]
Not recommended for plastic panels.

Snap-in models allow front mounting only.

For snap-in applications, the D sides of the the cutout must
have a .02 [.508] radius on the instllation side.

Case Dimensions

Part No. A B C D E F
(max.) (max.) (max.) ± .01 ± .01 ± .008
± .254 ± .254 ± .203
CS, CBS 1.22 .93 1.62 1.06 1.54 *  
30.99 23.62 41.17 26.92 39.12 *  
CE, CBE 1.74 .93 1.62 1.06 1.56 1.417
44.2 23.62 41.17 26.92 39.62 36.0
CFS, CHS 1.22 2.53 1.62 1.12 1.54*  
30.99 64.26 41.17 28.5 39.12*  
CFE, CHE 1.74 2.53 1.62 1.12 1.56 1.417
44.2 64.26 41.17 28.5 39.62 36.0
* ± .000
  ± .008

Ordering and Design Information

Click on any part number for 3D CAD models, customer drawings, distributor stock status and eCommerce Links. For more information refer to the Corcom Part Numbering System reference.

1CHS1 1CHE1 1CFS1 1CFE1
3CHS1 3CHE1 3CFS1 3CFE1
6CHS1 6CHE1 6CFS1 6CFE1
10CHS1 10CHE1 10CFS1 10CFE1
10CBS1 10CBE1 10CS1 10CE1
15CS1 15CE1 15CBS1 15CBE1

USA Customer Service: 1-800-468-2023
Corcom Products Direct: 1-847-680-7400
Germany: 49-89-6089-0
Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.