Skip to content
Search By: Close Search Selector
Home > Series > IEC > ED

ED Series

High Performance Compact RFI Power Line Filters with IEC Connectors

UL Recognized
CSA Certified
VDE Approved

15ED1, 15ED8 - UL, CSA: 15 Amps/250VAC
VDE: 10 Amps/250 VAC

Catalog Data Sheet

ED Series

The ED series filters are more effective than generalpurpose filters in applications where line-to-line and lowfrequency line-to-ground noise must be controlled; for example, to bring equipment into compliance with FCC conducted emissions standards.

The ED series offers significantly higher performance than comparably sized filters, especially at high frequencies, yet is in the EF series package which incorporates the IEC power line connector.

Models ED1, ED1C, and ED2 have .250” terminals on load side; ED4, ED4C, ED8, and ED8C have wire leads. Models 6ED1C, 10ED1C, 6ED4C, and 6ED8C additionally incorporate a separate ground-circuit inductor to isolate the equipment chassis from power line ground at RF frequencies.

 

Electrical Schematic

ED Models

ED-C Models

Resistor location for reference only

Specifications

Maximum leakage current, each line to ground:
  @ 120 VAC 60 Hz .22 mA
  @ 250 VAC 50 Hz .38 mA
     
Hipot rating (one minute):
  line to ground 1500 VAC
  line to line 1450 VDC
     
Operating Frequency: 50 / 60 Hz
     
Rated voltage (max.): 250 VAC
     
Rated Current: 1A to 15A *
  * refer to part number for rating
Minimum insertion loss in dB:
Line to ground in 50 ohm circuit
Current Rating Frequency - MHz
.15 .5 1 5 10 30
ED1, ED2, ED4, & ED8            
1A 24 35 42 49 52 54
3A 20 29 36 45 50 54
6A 14 23 30 41 45 50
10A 8 14 20 35 39 45
15A 4 9 12 28 34 40
ED1C            
6A 14 20 25 37 42 50
10A 8 14 20 35 39 45
ED4C, ED8C            
6A 14 20 25 37 42 50

Line to line in 50 ohm circuit
Current Rating Frequency - MHz
.15 .5 1 5 10 30
ED1, ED2, ED4, & ED8            
1A 3 15 20 37 37 36
3A 3 15 20 37 37 36
6A 3 15 20 31 35 34
10A 6 15 20 23 44 47
15A 6 18 23 33 44 47
ED1C            
6A 7 17 23 36 42 42
10A 6 15 20 23 44 47
ED4C, ED8C            
6A 7 17 23 29 38 42

Case Styles

ED1 & ED1C

 

 

ED2

Typical Dimensions
Terminals (3) .250 Holes (2) .07 Dia.
6.35 1.8
Slot .07 x .16 Mounting Holes (2)
 .132 Dia
1.8 x 4.1 3.35
    with .260 x 90° countersunk for#4 Flathead Screw

ED4 & ED4C

 

ED8 & ED8C

Typical Dimensions
Wire Leads 18AWG (min.) 4.0 Mounting Holes (2) .132 Dia
101.6 3.35

Recommended Panel Cutouts

Tolerance ± .005 [0.13]

Note 1: ED1, ED1C, ED8 and ED8C allow for front or back mounting.
Note 2: ED2, ED4 and ED4C allow back mounting only

Case Dimensions

Part No. A B C D E F
(max.) (max.) (max.) ± .015 (max.) (ref)
± .38
1ED1, 3ED1, 6ED1 2.21 1.19 0.81 1.575 1.98  
56.0 30.2 20.6 40.01 50.3  
1ED2, 3ED2, 6ED2 1.55 1.19 0.85 1.575 1.98  
39.4 30.2 21.6 40.01 50.3  
1ED4, 3ED4, 6ED4 1.55 1.19 0.85 1.575 1.98 .295
39.4 30.2 21.6 40.01 50.3 7.5
1ED8, 3ED8, 6ED8 1.55 1.19 0.81 1.575 1.98 .295
39.4 30.2 20.6 40.01 50.3 7.5
6ED4C 1.98 1.19 0.85 1.575 1.98 .295
50.3 30.2 21.6 40.01 50.3 7.5
6ED8C 1.98 1.19 0.81 1.575 1.98 .295
50.3 30.2 20.6 40.01 50.3 7.5
6ED1C,
10ED1, 10ED1C
15ED1 		2.62 1.19 0.81 1.575 1.98  
66.5 30.2 20.6 40.01 50.3  
15ED8 1.98 1.19 0.81 1.575 1.98  
50.3 30.2 20.6 40.01 50.3  
 

Ordering and Design Information

Click on any part number for 3D CAD models, customer drawings, distributor stock status and eCommerce Links. For more information refer to the Corcom Part Numbering System reference.

1ED1 6ED2
1ED2 6ED4
1ED4 6ED4C
1ED8 6ED8
3ED1 6ED8C
3ED2 10ED1
3ED4 10ED1C
3ED8 15ED1
6ED1 15ED8
6ED1C  
   
Line Cord GA400
Insulating Boot FA601

 
USA Customer Service: 1-800-468-2023
Corcom Products Direct: 1-847-680-7400
Germany: 49-89-6089-0
Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.