Skip to content
Search By: Close Search Selector
Home > Series > IEC > EC

EC Series

High Performance Compact RFI Power Line Filters with IEC Connectors

UL Recognized
CSA Certified
VDE Approved

Catalog Data Sheet

EC Series

The EC series RFI power line filters provide the highest attenuation of any standard filter available in a package size limited by the dimensions of the integral IEC connector. These filters combine high common-mode inductance with high differential-mode capacitance and minimal parasitic elements, for effective attenuation of line-to-ground and line-to-line noise across the frequency range.

Performance and applications are similar to those of the ED series, but with higher differential-mode performance in most applications, due to an additional capacitor on the load side.

 

Electrical Schematic

Resistor location for reference only

Specifications

Maximum leakage current, each line to ground:
  @ 120 VAC 60 Hz .22 mA
  @ 250 VAC 50 Hz .38 mA
     
Hipot rating (one minute):
  line to ground 1500 VAC
  line to line 1450 VDC
     
Operating Frequency: 50 / 60 Hz
     
Rated voltage (max.): 250 VAC
     
Rated Current: 1A to 10A *
  * refer to part number for rating
Minimum insertion loss in dB:
Line to ground in 50 ohm circuit
Current Rating Frequency - MHz
.15 .5 1 5 10 30
1A 25 35 40 50 50 50
3A 20 30 37 47 48 50
6A 15 22 25 40 45 50
10A 7 14 20 35 39 48
Line to line in 50 ohm circuit
Current Rating Frequency - MHz
.15 .5 1 5 10 20 30
EC1, EC2 & EC8 Models              
1A 5 35 50 60 60 40 40
3A 5 25 45 60 55 34 34
6A 10 10 40 65 60 40 40
10A 10 10 27 65 56 38 38
EC4 Models              
1A 5 35 50 60 60 33 33
3A 5 30 45 60 55 34 34
6A 10 10 40 65 60 33 33

Case Styles

EC1

 

EC2

Typical Dimensions
Terminals (3) .250 Holes (2) .07 Dia.
6.35 1.8
Slot .07 x .16 Mounting Holes (2)
 .132 Dia
1.8 x 4.1 3.35
    with .260 x 90° countersunk for#4 Flathead Screw

EC4

EC8

Typical Dimensions
Wire Leads 18AWG (min.) 4.0 Mounting Holes (2) .132 Dia
101.6 3.35

Recommended Panel Cutouts

Tolerance ± .005 [0.13]

Note 1: EC1 and EC8 allow for front or back mounting.
Note 2: EC2 and EC4 allow back mounting only

Case Dimensions

Part No. A B C D E F
(max.) (max.) (max.) ± .015 (max.) (ref)
± .38
1EC1, 3EC1,
6EC1, 10EC1		 2.62 1.19 0.81 1.575 1.98  
66.5 30.2 20.6 40.01 50.3  
1EC2, 3EC2,
6EC2		 1.97 1.19 0.85 1.575 1.98  
50.0 30.2 21..6 40.01 50.3  
1EC4, 3EC4,
6EC4		 1.97 1.19 0.85 1.575 1.98 .295
50.0 30.2 21.6 40.01 50.3 7.5
1EC8, 3EC8,
6EC8		 1.98 1.19 0.81 1.575 1.98 .295
50.3 30.2 20.6 40.01 50.3 7.5
 

Ordering and Design Information

Click on any part number for 3D CAD models, customer drawings, distributor stock status and eCommerce Links. For more information refer to the Corcom Part Numbering System reference.

1EC1 6EC1
1EC2 6EC2
1EC4 6EC4
1EC8 6EC8
3EC1 10EC1
3EC2  
3EC4  
3EC8  
   
Line Cord GA400
Insulating Boot FA601

 
USA Customer Service: 1-800-468-2023
Corcom Products Direct: 1-847-680-7400
Germany: 49-89-6089-0
Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.