Skip to content
Home > Series > DC > DCP

DCP Series

The CHAMELEON Adaptable Module for General Purpose, DC Applications

UL Recognized
CSA Certified
TUV Approved

Catalog Data Sheet

DCP Series

full flexibility of design in the most compact package. It is a general purpose filter specifically designed for DC applications up to 80VDC. This module comes in snap-in or flange mount versions for easy mounting. It also allows for a single or dual fuse option.

The DC version of the “P Series” was designed to address the increasing demand for filtering on central office equipment and customer premises equipment, but not restricted to this type of equipment. Some examples include routers, desktop servers and switches multiplexors, aggregators, concentrators, etc.

The DC versions of the P Series mates with a standard MOLEX connector (HCS Series) which is readily available and better prevents accidental connection to AC power.

Electrical Schematic

 

Resistor location for reference only

Specifications

Hipot rating (one minute):
  line to ground 2250 VDC
  line to line 1450 VDC
     
Fuse (not included): Accepts one or two fuses
.25" x 1.25" or 5 x 20mm
Conversion clip provided on fuseholder for single fuse models
     
Rated voltage (max.): 80 VDC
     
Rated Current: 3A to 10A *
  * refer to part number for rating
   
Terminals: .187 x .032 [4.8 x .81] terminal tabs
Recommended for use with mating connector, no solder
 
Operating ambient temperature range at rated current Ir -10°C to +55°C
In an ambient, Ta, higher than +55° C, the maximum operating current, Io, is calculated as follows: Io=Ir√(90-Ta/35 )
 
Minimum insertion loss in dB:
Line to ground in 50 ohm circuit
Current Rating Frequency - MHz
.03 .1 .15 .5 1 3 5 10 30
3A 7 17 21 27 33 40 44 50 32
6A - 8 12 17 23 32 36 44 30
10A - 3 5 10 13 23 27 35 27
 
Line to line in 50 ohm circuit
Current Rating Frequency - MHz
.10 .15 .5 1 3 5 10 30  
3A 2 4 12 15 30 48 50 45  
6A 2 4 12 15 22 42 55 45  
10A 2 4 12 15 22 42 55 45  
 

Case Styles

PE

PS

Typical Dimensions
Terminals: .187 x 0.032 Holes: .055 Dia ± .004
4.8 x .81 1.5 ± .10
Slot: .06 x .115 ± .004 Mounting Holes (PE Only)
Countersunk
.135 Dia
1.52 x 2.92 ±.10 3.43

 

 

Recommended Panel Cutout

 

 

Note: The external edges (installation side) on the "D" sides of the cutout should have a minimum .020" radious. for optional retention against extration, the corresponding inner edge should be sharp, without paint or coatings. Edg coatings, including anodization are also discouraged for good shield contact.

Part Numbering Schematic

Case Dimensions

Part No. A B C D E
(max.) (max.) (max.) ±.010 (max.)
± .25
DAF1 2.15 1.12 0.81 1.575 1.98
54.61 28.45 20.57 40.01 50.29
DAS1 1.98 1.10 0.81 0.96* 1.41
50.29 27.94 20.57 24.38* 35.81
DAFP 1.54 1.12 0.81 1.575 1.98
39.12 28.45 20.57 40.01 50.29
* Max. dimension

Ordering and Design Information

Click on any part number for 3D CAD models, customer drawings, distributor stock status and eCommerce Links. For more information refer to the Corcom Part Numbering System reference.

PE000DD3D PS000DD3D
PE000DD6D PS000DD6D
PE000DDXD PS000DDXD
PE000SD3D PS000SD3D
PE000SD6D PS000SD6D
PE000SDXD PS000SDXD

Mating Connectors

GA210 - Custom connector assembly with 2, 36" long 18 gauge wires to mate with DA Series filter

Molex Component Numbers:
03-12-1026: Connector housing to mate with DA Series
18-12-1222: Female Terminal (3 needed per housing)

 
USA Customer Service: 1-800-468-2023
Corcom Products Direct: 1-847-680-7400
Germany: 49-89-6089-0
Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change.